Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
pinctrl-0 = <&i2c1_pins>;
status = "okay";
};
+
+&usbphy {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
#address-cells = <1>;
#size-cells = <0>;
};
+
+ usbphy: phy@1c1b810 {
+ compatible = "allwinner,sun50i-a64-usb-phy",
+ "allwinner,sun8i-a33-usb-phy";
+ reg = <0x01c1b810 0x14>, <0x01c1b800 0x4>;
+ reg-names = "phy_ctrl", "pmu1";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci1: usb@01c1b000 {
+ compatible = "allwinner,sun50i-a64-ehci",
+ "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@01c1b400 {
+ compatible = "allwinner,sun50i-a64-ohci",
+ "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "enabled";
+ };
};
};
#define SUNXI_USB2_BASE 0x01c1c000
#endif
#ifdef CONFIG_SUNXI_GEN_SUN6I
-#ifdef CONFIG_MACH_SUN8I_H3
+#if defined(CONFIG_MACH_SUN8I_H3) || defined(CONFIG_MACH_SUN50I)
#define SUNXI_USBPHY_BASE 0x01c19000
#define SUNXI_USB0_BASE 0x01c1a000
#define SUNXI_USB1_BASE 0x01c1b000
}
}
-#if defined CONFIG_MACH_SUN8I_H3
+#if defined(CONFIG_MACH_SUN8I_H3) || defined(CONFIG_MACH_SUN50I)
static void sunxi_usb_phy_config(struct sunxi_usb_phy *phy)
{
+#if defined CONFIG_MACH_SUN8I_H3
if (phy->id == 0)
clrbits_le32(SUNXI_USBPHY_BASE + REG_PHY_UNK_H3, 0x01);
-
+#endif
clrbits_le32(phy->base + REG_PMU_UNK_H3, 0x02);
}
#elif defined CONFIG_MACH_SUN8I_A83T
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
* clocks resp. phys.
*/
priv->ahb_gate_mask = 1 << AHB_GATE_OFFSET_USB_EHCI0;
-#ifdef CONFIG_MACH_SUN8I_H3
+#if defined(CONFIG_MACH_SUN8I_H3) || defined(CONFIG_MACH_SUN50I)
extra_ahb_gate_mask = 1 << AHB_GATE_OFFSET_USB_OHCI0;
#endif
- priv->phy_index = ((u32)hccr - SUNXI_USB1_BASE) / BASE_DIST;
+ priv->phy_index = ((uintptr_t)hccr - SUNXI_USB1_BASE) / BASE_DIST;
priv->ahb_gate_mask <<= priv->phy_index * AHB_CLK_DIST;
extra_ahb_gate_mask <<= priv->phy_index * AHB_CLK_DIST;
priv->phy_index++; /* Non otg phys start at 1 */
sunxi_usb_phy_init(priv->phy_index);
sunxi_usb_phy_power_on(priv->phy_index);
- hcor = (struct ehci_hcor *)((uint32_t)hccr +
+ hcor = (struct ehci_hcor *)((uintptr_t)hccr +
HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
return ehci_register(dev, hccr, hcor, NULL, 0, plat->init_type);
{ .compatible = "allwinner,sun8i-a83t-ehci", },
{ .compatible = "allwinner,sun8i-h3-ehci", },
{ .compatible = "allwinner,sun9i-a80-ehci", },
+ { .compatible = "allwinner,sun50i-a64-ehci", },
{ }
};
{ .compatible = "allwinner,sun8i-a83t-ohci", },
{ .compatible = "allwinner,sun8i-h3-ohci", },
{ .compatible = "allwinner,sun9i-a80-ohci", },
+ { .compatible = "allwinner,sun50i-a64-ohci", },
{ }
};
* A64 specific configuration
*/
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_SUNXI
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#endif
+
#define CONFIG_SUNXI_USB_PHYS 1
#define COUNTER_FREQUENCY CONFIG_TIMER_CLK_FREQ